A steep driveway is a better starting point than the biggest number on a motor spec sheet. Start with the hill you need to climb, the weight you’ll carry, and the speed and pedaling effort you can comfortably maintain. Then look for a bike or trike with gearing that lets the motor help at that speed, a battery that can finish the ride, and a shop that can service the system.
The short answer
Choose a mid-drive for the way you ride. For hills, compare the lowest gear and sustained motor output at your cadence. For touring, size the battery in watt-hours and check replacement availability. For a recumbent trike, put controlled starts and rear-wheel traction on the test-ride list.
In this guide
- What a mid-drive does
- How to read torque, watts and cadence
- How gears change the pull at the wheel
- How much power your hill takes
- Battery size and range
- Major brands and motor families
- What to check before you buy
- Common questions
What a mid-drive motor does
A mid-drive sits at the pedals. On a conventional bicycle that’s near the bottom bracket. On a tadpole recumbent trike it can be out front on the boom. The motor adds to your effort at the cranks and sends power through the drivetrain to the driven wheel. A hub motor applies its output at the wheel hub and keeps the same motor-to-wheel ratio when you shift the bike’s gears.
On a mid-drive, shifting to a lower gear lets the motor and rider turn the cranks faster at the same road speed and increases the torque at the wheel. That’s useful on hills, especially with touring gear or a heavy trike. The chain, cassette, idlers and other drivetrain parts also carry that combined load. Ease pedal pressure for shifts unless your drivetrain is designed for shifting under load, and shift to an easier gear before you stop or begin a steep climb. Bosch’s gearing and range guidance.
On a demo ride, pay attention to when assistance starts and how it comes in. A torque sensor measures how hard you push. A cadence sensor detects pedal rotation. Some systems blend these and other sensors, and the tuning determines how they feel. Try a gentle start, a slow turn, a pause in pedaling and a restart. If throttle assistance matters to you, try it on the exact build in a permitted setting. Walk assist is designed to help while you’re walking beside the bike.
Torque, watts and cadence
- Torque (Nm) measures twisting force. For the equations below, use torque at the crank or equivalent drive output. A motor’s maximum torque tells you one limit of its output.
- Mechanical power (W) tells you how fast the motor can do work. Rated continuous output and short-duration maximum output answer different questions. Ask how much power the motor can hold at the cadence and for the duration you need.
- Electrical input (W) is what the motor and controller draw from the battery, roughly volts times amps at that moment. Some of that energy becomes heat. The mechanical watts at the cranks will be lower than the electrical input while the motor is delivering assistance.
- Cadence (rpm) is how fast you turn the pedals. Peak torque and peak power can occur at different cadences. Support modes, rider input, firmware, temperature and battery limits also affect what the system delivers.
Mechanical power (W) = torque (Nm) × 2π × cadence (rpm) ÷ 60. If a motor holds 60 Nm at 60 rpm, it delivers about 377 W. If it can hold the same torque at 80 rpm, it delivers about 503 W. The word if matters. A published maximum torque figure alone leaves the rest of the power curve unknown. For a concrete example, Shimano lists the EP600 and EP801 at the same 85 Nm and 250 W continuous rating, with different top outputs of 500 W and 600 W, respectively. Shimano EP600 and EP801 comparison.
Check the kind of riding that generated the number. A launch boost can help you get going. A long climb asks the motor and battery to keep delivering power as they heat up. For independent comparisons, look for test conditions that state cadence, rider input, firmware, cooling and time under load. E-Bike Lab publishes a test protocol and a 20-minute load comparison for selected motors. Dynamometer test method and thermal test results.
What the lowest gear does for you
Write down the number of teeth on the front chainring and on the largest rear cog. You can often read the numbers on the parts themselves or find them in the seller’s specifications. For a conventional chain drive, these three relationships connect the motor to the road.
- Gear inches ≈ driven-wheel rolling diameter in inches × front teeth ÷ rear teeth.
- Rear-wheel torque ≈ crank-output torque × rear teeth ÷ front teeth × drivetrain efficiency.
- Road speed in mph ≈ π × gear inches × cadence ÷ 1,056.
Lower gear inches mean a shorter distance traveled per pedal revolution. If a bike has an internal-gear hub, gearbox or unusual chainring reduction, use the complete effective ratio. For the wheel diameter, measuring one revolution under load and dividing the distance by π is more precise than using the size printed on the tire.
Here’s the difference with a 26-inch effective rear wheel and a 38-tooth chainring. A 24-tooth rear cog gives about 41 gear inches and about 41 rpm at 5 mph. A 46-tooth cog gives about 21.5 gear inches and about 78 rpm at the same speed. A lower gear gives you more leverage and can put the motor in a more productive cadence range.
Tire size changes the push at the pavement too. Force at the tire ≈ wheel torque ÷ loaded wheel radius. With the same gearing and wheel torque, a smaller driven wheel produces more force at the contact patch and less road speed at a given cadence. For a tadpole trike, use the driven rear wheel in this calculation.
How much power does your hill take?
Collect four inputs. Use the steepest meaningful grade, the length of that climb, the total loaded weight of rider, bike or trike, battery and gear, and your target climbing speed. Grade is rise divided by horizontal distance. A 12% grade rises 12 feet in 100 horizontal feet. Check both the steep pitch where you may have to restart and the longer stretch where you need steady assistance.
The calculation
At a steady speed in still air, the driven wheel has to overcome gravity, rolling resistance and air drag. An adaptation of the road-cycling power model gives the following wheel-side estimate. Martin and colleagues’ cycling power model.
- Wheel power = [m × g × (sin θ + Crr × cos θ) + ½ × ρ × CdA × v²] × v.
- Motor mechanical power ≈ wheel power ÷ drivetrain efficiency − rider power at the cranks, with a floor of zero.
- Battery power for assistance ≈ motor mechanical power ÷ motor-and-controller efficiency. Add electrical accessories separately if material.
Use mass m in kilograms, ground speed v in meters per second, gravity g of 9.81 m/s², and slope angle θ = arctan(grade ÷ 100), with grade entered as a percentage such as 12. Crr is the rolling-resistance coefficient, ρ is air density in kg/m³ and CdA is effective drag area in m². In a headwind, air drag uses the speed through the air, while the final multiplier is still ground speed.
Read the climbing chart as a table
| Grade | 4 mph | 5 mph | 7 mph |
|---|---|---|---|
| 5% | 135 W | 171 W | 244 W |
| 8% | 207 W | 260 W | 368 W |
| 12% | 301 W | 377 W | 533 W |
| 15% | 370 W | 464 W | 655 W |
| 20% | 484 W | 606 W | 854 W |
| 22% | 529 W | 662 W | 932 W |
Worked example for a 300-pound loaded setup
- At 5 mph up a 12% grade, the model gives 377 W at the wheel. At 95% drivetrain efficiency, that calls for about 397 W at the cranks.
- If you can supply 100 W at the cranks, the motor needs to add about 297 W mechanically. With the 38/46 gearing above, that’s about 36 Nm at 78 rpm. With the 38/24 gearing it’s about 69 Nm at 41 rpm. Both figures describe the same speed and hill.
- At an illustrative 80% motor-and-controller efficiency, battery draw for assist is about 371 W. A half-mile climb at that speed lasts six minutes and uses about 37 Wh for the climb under those assumptions.
At a 20% grade and the same 5 mph, wheel demand rises to about 606 W, or roughly 538 W of sustained motor output with the same rider effort and drivetrain efficiency. At 4 mph the model calls for about 484 W at the wheel. That’s a useful reduction, provided the lowest gear still gives you a comfortable cadence and the motor enough speed to work effectively. Substitute your own sustainable effort. A rider contributing 50 W will need 50 W more from the motor in the same example.
On a trike with one driven rear wheel, wet pavement, loose gravel and weight distribution can limit available grip. For a steep driveway or a recurring climb, ask the seller to help you evaluate a controlled uphill restart and a sustained climb with comparable load and surface. Include braking on the descent in the evaluation. Bring your numbers to the Pickens Cycles E-Assist Finder for a first-pass comparison.
Battery size and range
Watt-hours (Wh) measure stored energy. Multiply nominal voltage by amp-hours when you need a quick estimate. For example, 36 V × 14 Ah is about 504 Wh, and 48 V × 14 Ah is about 672 Wh. Use the pack’s published watt-hours when available. A pack’s voltage, discharge limit and compatibility with the controller are separate from how much energy it stores.
Estimated range (mi) = energy budget for the ride (Wh) ÷ energy use (Wh per mile). If you start with 625 Wh and set aside 15% for a reserve, your planning budget is about 531 Wh. At 18 Wh per mile, that’s about 30 miles. A 40-mile trip at 18 Wh per mile would require about 847 Wh of available starting energy to finish with that same reserve (40 × 18 ÷ 0.85).
Read the range chart as a table
| Battery | 12 Wh/mi | 18 Wh/mi | 25 Wh/mi |
|---|---|---|---|
| 500 Wh | 35.4 | 23.6 | 17.0 |
| 625 Wh | 44.3 | 29.5 | 21.2 |
| 750 Wh | 53.1 | 35.4 | 25.5 |
Use a representative ride to improve the estimate. If your system reports energy used, divide that figure by miles ridden and plan for the most demanding part of the route. Climbing alone adds up quickly. Lifting a 300-pound loaded bike and rider 1,000 vertical feet requires about 113 Wh of mechanical work against gravity. That’s one part of the ride’s energy budget. Your pedaling shares the work, and rolling resistance and conversion losses affect the energy drawn from the pack.
Major mid-drive brands and what they offer
These are representative systems you’ll encounter when shopping for a complete bike, a trike or a conversion. Specs were checked in November 2026. The table distinguishes rated power from advertised maximum output. It includes clearly identified global platform specs where U.S. builds may differ. Ask the seller for the model code, installed battery and enabled settings for the exact bike on offer.
On a phone, swipe the comparison table to see all columns.
| Brand | Representative models and published output | What to check on the bike |
|---|---|---|
| Bosch | Active Line Plus spans multiple generations. One recumbent example, the Villager eCAT, lists 50 Nm. Performance Line lists 75 Nm / 600 W max. Lightweight SX lists 60 Nm / 600 W max. Eligible Gen 5 CX (BDU384Y) builds list up to 120 Nm / 750 W max with the applicable performance upgrade and configuration. Bosch also offers PX for touring and Cargo Line for heavier loads. | Confirm generation, as-delivered settings, compatible batteries and a shop that can diagnose the exact bike. Bosch system catalog, CX upgrade conditions, Villager eCAT specifications. |
| Shimano | EP5 (DU-EP500) offers 60 Nm for city and leisure builds. EP6 (DU-EP600) and EP8 (DU-EP801) both list 85 Nm and 250 W continuous, with 500 W and 600 W top output respectively. | Identify the exact EP8 model code. AUTO SHIFT and FREE SHIFT features depend on the specific compatible drivetrain and setup. EP5, EP6 vs. EP801, shifting compatibility. |
| Bafang | The current OEM-style M510 listing shows 110 Nm / 250 W rated. An earlier workbook lists 95 Nm for MM G522.250.C. Bottom-bracket conversions include the M315 example at 100 Nm / 500 W rated and M615 variants up to 160 Nm with 750 or 1,000 W rated. | Read the motor label and verify kit fit, exact controller, battery, throttle and support. Higher-rated kits need particular attention to where the finished vehicle can be used. M510, Bafang OEM workbook, M315, M615. |
| Yamaha / Giant | Yamaha’s 36 V PWseries S2 and PW-X3 list 75 Nm and 85 Nm. Its global 48 V PW-X4 lists 100 Nm in boost / 800 W max. Giant lists 75 Nm for SyncDrive Sport 2 and 85 Nm for Pro 2 in its U.S. lineup. It publishes 100 Nm / 800 W peak for Pro 3X on its U.K. site. | Some SyncDrive units were co-developed with Yamaha. Confirm the build, battery and local service through the bike brand. Yamaha 36 V catalog, PW-X4, Giant U.S. lineup, Pro 3X platform. |
| Specialized | The compact SL 1.2 on selected Levo SL models lists 50 Nm / 320 W. The current U.S. S-Works Turbo Levo 4 page lists 111 Nm / 850 W for its 3.1 motor. | Shop by trim and firmware. Specialized integrates the motor, battery and controls into its Turbo bikes. SL 1.2 build, S-Works 3.1 build. |
| Avinox | M1, M2 and M2S list up to 105, 110 and 130 Nm in regular modes, or 120, 125 and 150 Nm in Boost. Avinox publishes platform peaks of 1,000, 1,100 and 1,500 W. M2S reaches its top figure in Boost with specified batteries and lists 1,300 W with FS600 or FS800. | A high-output e-MTB option. Check how long Boost is available, which battery ships with the bike, the delivered settings and the rules where you ride. Avinox power and torque by mode. |
| Aventon | Aventon publishes 100 Nm and 250 W continuous / 750 W peak for the A100 used on the Ramblas. The Current ADV’s Ultro X is listed at 110 Nm, or 120 Nm in Boost. | Identify the motor on the exact bike and which dealer can handle diagnostics and parts. Aventon A100 specifications, Current ADV specifications. |
| SRAM / Brose | SRAM Eagle Powertrain uses a Brose-derived drive unit. Propain lists 90 Nm / 680 W peak on its Ekano 2 CF with Eagle Powertrain. The system integrates compatible Eagle Transmission components for automatic shifting. | Useful to evaluate if integrated shifting is a priority. Ask who services the complete drive system and battery on your bike. SRAM system overview, Propain build specifications, Blister’s drive-unit review. |
| TQ / FAZUA | TQ HPR60 lists 60 Nm / 350 W. FAZUA RIDE 60 lists 60 Nm / 450 W peak with Boost. Both families emphasize compact integration and lower weight. | Evaluate the lowest gear, exact battery capacity, range extender availability and assistance at the cadence you ride. TQ HPR60, FAZUA RIDE 60. |
Another design integrates shifting into the motor housing. Pinion’s MGU combines a mid-drive with a 9- or 12-speed gearbox. Other systems can pair a motor with an automatic rear hub such as Enviolo AUTOMATiQ. If shifting at a stop is important to you, verify what the exact system can do and what low ratio is available. Check drivetrain limits and approved pairings for high-torque builds. Pinion MGU, Enviolo AUTOMATiQ and hub compatibility guidance.
What to check before you buy
Match the system to your ride
- Mostly paved paths and casual touring. Prioritize smooth low-speed assist, a comfortable cadence, usable battery range and a shop close to home or along the routes you travel. Try riding with assist off so you know how the complete bike feels when the battery is low.
- Long or steep hills, loaded touring and cargo. Ask for the lowest effective ratio, power the motor can sustain at your climbing cadence, and any load restrictions. Make sure the complete bike’s brakes, drivetrain and weight rating suit the route and load.
- Recumbent trikes. Check the rear wheel diameter and low gear, how the motor responds when you start from a stop, and how easy the controls are to reach from the seat. Fold the trike, remove the battery if designed for removal, and check that your vehicle or rack can handle the actual size and weight.
- Conversions. Ask the frame or trike maker about the specific kit. Check bottom-bracket shell dimensions, boom strength and retention on a trike, chainline, crank and heel clearance, idlers, the approved battery mounting location and how the kit affects the folding mechanism and warranty. Price the complete installation, including battery, charger, labor and any drivetrain or brake work.
Check access, battery safety and service
Under the common U.S. three-class model, Class 1 is pedal assist to 20 mph, Class 2 can provide motor-only assistance up to 20 mph, and Class 3 is pedal assist up to 28 mph. State definitions and trail access vary. Federal consumer-product law separately defines a low-speed electric bicycle using criteria that include fully operable pedals, a motor of less than 750 W and a specified motor-only speed test. Verify the complete vehicle’s classification with the seller and check the rules of the road or trail manager. If you ride in South Carolina, consult the state’s definition and your route’s rules. PeopleForBikes class definitions, 15 U.S.C. § 2085, South Carolina Code, § 56-1-10.
Ask the seller for a certification listing or certificate number for the exact electrical system. UL 2849 addresses the e-bike electrical system, including the drive, battery and charger combination. UL 2271 applies to battery packs for light electric vehicles. Use the charger and replacement battery approved by the manufacturer for the exact system. UL Solutions on e-bike electrical systems, UL 2271 scope, CPSC charger guidance.
Get five answers in writing. Ask for the exact motor and battery codes, a replacement battery price and lead time, the name of a shop that can run diagnostics, who pays for warranty labor and shipping, and how service works if you travel or buy online. A motor family with a dealer locator is a starting point. Call the shop and confirm it supports your exact bike or trike. Bosch dealer diagnostics, Shimano dealer locator.
Common questions
Is a 750 W Bafang stronger than a 250 W Bosch or Shimano?
First find out what each label measures. It might be rated motor power, maximum mechanical output or battery-side electrical input. Then compare the exact models’ output at the cadence you can hold, the lowest gear, wheel size and the climb duration. For a real buying decision, compare the complete bikes or trikes on similar terrain and load.
Can a 70 Nm motor get me up a 20–22% driveway?
It depends on the length of the slope, loaded weight, start, gearing, traction and how much assistance the motor can sustain. In the 300 lb example above, 20–22% at 5 mph needs roughly 606–662 W at the wheel. A short, dry ramp you enter with momentum can feel different from a long climb or a wet uphill restart. Ask for a controlled demonstration on a comparable grade before buying for that use.
Will a bigger battery make the same motor more powerful?
Usually the capacity increase buys more range. Some systems allow more peak power only with certain approved batteries or configurations. Check the manufacturer’s motor-and-battery pairing and compare the replacement price before deciding.
Put your own route into the numbers.
Bring your loaded weight, grade, front chainring size and rear cassette range to the Pickens Cycles E-Assist Finder. If you’re shopping for a trike, see what to check on a recumbent trike test ride.